My heap - Page 2

black88coupe · 01-31-2010, 01:09 PM

Quote:

Originally Posted by teef racing

nice work, what turbo kit is that?

Thanks. It's a Ponydown Performance kit.

357windsor · 02-04-2010, 03:26 PM

Any more progress?

black88coupe · 02-05-2010, 04:47 AM

Quote:

Originally Posted by 357windsor

Any more progress?

Been busy with work/ family. Gonna hit it this weekend for sure though.

357windsor · 02-05-2010, 07:50 AM

Quote:

Originally Posted by black88coupe

Been busy with work/ family. Gonna hit it this weekend for sure though.

Post more progress pics when you can.

black88coupe · 02-05-2010, 10:34 PM

Quote:

Originally Posted by 357windsor

Post more progress pics when you can.

For sure. Was gonna work on it tonight but my relief called off so I got stuck working 16hrs. today unexpectadly. AAARRRGGGHHHH!

PizzaBoy · 02-05-2010, 10:45 PM

Quote:

Originally Posted by black88coupe

For sure. Was gonna work on it tonight but my relief called off so I got stuck working 16hrs. today unexpectadly. AAARRRGGGHHHH!

Hey you are every where huh?

357windsor · 02-06-2010, 11:35 AM

Quote:

Originally Posted by black88coupe

For sure. Was gonna work on it tonight but my relief called off so I got stuck working 16hrs. today unexpectadly. AAARRRGGGHHHH!

That sucks

black88coupe · 02-06-2010, 03:58 PM

Quote:

Originally Posted by PizzaBoy

Hey you are every where huh?

You too if ya keep finding me!

black88coupe · 02-06-2010, 07:20 PM

Quote:

Originally Posted by 357windsor

Any more progress?

I got the pass side floorpan cut out. Trimmed off some brake and fuel lines as well. Not much time to do anything else. Gonna try and do more tomorrow.

black88coupe · 02-06-2010, 09:34 PM

Since I'm stuck in the house I decided to try and get some work done on my Mega-Squirt EFI controller. This is a very slow moving long term project that I have been working on for my car.

teef racing · 02-07-2010, 12:26 AM

Quote:

Originally Posted by black88coupe

Thanks. It's a Ponydown Performance kit.

i was looking at a ponydown kit, hows the quality? you happy with the fit?

black88coupe · 02-07-2010, 08:00 AM

Quote:

Originally Posted by teef racing

i was looking at a ponydown kit, hows the quality? you happy with the fit?

It's not the most expensive kit on the market but I would say the quality is good.

black88coupe · 02-08-2010, 03:46 PM

Picked up a couple Paxton billet filters. They came with two NIB 40 micron and two NIB 10 micron elements. Gonna run the 40 micron off the tank in front of my pumps and the 10 micron after the pumps. Paid $80 for everything.

black88coupe · 02-15-2010, 08:29 PM

Spent about 2.5hrs. in the garage today. Got some sheetmetal trimmed out to allow the pass. side 2 X 3 frame rails to be installed. Also did the last of the welding on the drivers side for now. Got a little bit more welding left to do but I gotta wait until I start installing my cage to finish that up. Gonna start fitting the pass. side rail soon.

black88coupe · 02-16-2010, 10:02 PM

I spent about 1.5hrs. in the garage tonight. Got the longest section of frame rail made up for the pass. side. It's the one that extends back from the firewall to the rear. Little bit of finish work to do on it and it'll be ready to be welded in permanently. The rest should go real quick since they are smaller pieces that are pretty simple to make and install. I'm gettin' pumped to see this thing back on the ground. I gotta re-assemble my rear axle. I can probably do that at work when I'm working on the weekend when nobody is around.