Looking for a .30 over 302 block.

[Casper302]

Just block, unless you got a good lower compression ratio piston's (like 10.1)

I got a garrett turbo to trade and cash. Has to be .30 over. Wanted to go turbo but found out I do not have the money to finish it befor the season start's so I am gonna spray the shit out of this motor.


Let me know.

bmxrider_03@hotmail.com

(734) 641-0478, Randy Jr. After 9 Pm.

[Strtracer]

Randy, PM me with what you are looking for(roller/non-roller) and how much you can afford $$$$ wise, no trades, I might be able to set you up with a guy I know.

[Casper302]

Mike Check Pm's

[357windsor]

I got a 306 short block I pulled out of a 85 mustang GT parts car. Was told it has Trw pistons & b-cam. Not sure of the compression though. I got a windsor so I don't need it.Asking $450 o.b.o. Pm me if you want to check it out. Have the stock pan and pushrods to for it also. Thanks

[Casper302]

I got a 306 short block I pulled out of a 85 mustang GT parts car. Was told it has Trw pistons & b-cam. Not sure of the compression though. I got a windsor so I don't need it.Asking $450 o.b.o. Pm me if you want to check it out. Have the stock pan and pushrods to for it also. Thanks


Check PM's! Quick ??? does it have a crank?

[357windsor]

pm sent

[NTIMID8]

Check with Raj aka Fryguy302 on Motown.

I think he has one and its been for sale for some time

Phil

[Casper302]

pm sent


Check Pm's I called today around 1:30 PM.

[357windsor]

Check Pm's I called today around 1:30 PM.

Tried callind last night around 9:30 and 10 ish. Going to be out for most of the morning. Let me know when I can call you. I got someone to deliver the motor. Thanks

[Casper302]

Tried callind last night around 9:30 and 10 ish. Going to be out for most of the morning. Let me know when I can call you. I got someone to deliver the motor. Thanks


ANy time today after 6 PM

[357windsor]

ANy time today after 6 PM

I'll call you after 6pm

[Casper302]

I'll call you after 6pm


Cool, I get home a round 6:20 - 6:30.

[Casper302]

Hey Matt, let me know when you find out if it is .30 over.

[357windsor]

no problem.I'll find out asap. Thanks

[Casper302]

no problem.I'll find out asap. Thanks


Cool thank's, best way to tell is the marking's on the piston's.

[357windsor]

PM sent

[357windsor]

Sorry the shrtblock turned out to be a std bore. Hopefully you find a 30 over block. I'll ask around and see if anyone I know has one. :)

[Casper302]

TTT Still looking.

[Casper302]

Anyone???

[Strtracer]

It costs less than a $100 to get a block bored +.030($8-10 a hole), you should look for a standard block and just get it prepped using your new pistons as guide. Not all +.030 pistons are the same size.

[Casper302]

It costs less than a $100 to get a block bored +.030($8-10 a hole), you should look for a standard block and just get it prepped using your new pistons as guide. Not all +.030 pistons are the same size.


Well this I know. I still cant make up my mind.

Still looking for part's.

Hey Mike we got another Capri for my brother and my dad wanted to know about that motor you have for sale, does it have a fly wheel and Dampner??

[Strtracer]

Still available, comes with flexplate and damper

[Casper302]

Still available, comes with flexplate and damper


I will let him know once I get home. ;)

[357windsor]

If you decide to go with a std bore, I know a guy in Mt Clemens has two blocks and is asking $75 each. Hope everything works out for ya!!